operators
New Jersey Door Works carries LiftMaster brand and Napoleon/Lynx brand operators of all types for all commercial and industrial applications.
No matter your door or grille type, no matter the size, no matter how many times it's used in a given day, no matter how rugged or quiet it needs to be, we have the right operator for your application.
Click HERE to see our web page on Commercial Gates and Gate Operators.
Use New Jersey Door Works for:
- PURCHASE OF ALL TYPES OF OPERATORS
- INSTALLATION
- SERVICE
- PARTS
- REMOTE CONTROLS
- KEYLESS ENTRY PADS
- ALL OTHER ACCESSORIES AND ACCESS PRODUCTS
- PREVENTIVE MAINTENANCE
- SAFETY EDGES AND SAFETY EYES
Spotlight: Liftmaster Brand Model T Industrial-Duty Trolley Operator
for Standard Lift Sectional Doors
Model T is an industrial-duty trolley operator for standard lift section doors. It features a low profile and industrial ball bearings on the output shaft.
LOGIC 3.O TECHNOLOGY (L3)
Added Value
-
Built-in 3-channel, 315MHz radio receiver accepts up to 23 Security+® or unlimited DIP switch remotes. 3-button remotes can be programmed for OPEN/CLOSE/STOP operation
-
Maintenance Alert System™ establishes a routine maintenance schedule based on the number of cycles or calendar date. Includes self-diagnostic system that allows you to troubleshoot up to eight different error codes
-
Timer-to-Close allows programming in 5-sec or 1-min increments. Commercial or industrial photo-eyes required
-
Thermal motor overload can be easily reset from the 3-button floor level control station
Reliability & Programming Simplicity
-
Switchless motor eliminates stuck start switch and motor malfunctions on single-phase operators
-
All high-voltage connections have been removed from the board for safety and ease of service
-
Diagnostic LEDs speed installation and troubleshooting
-
Motor direction jumper lets you change motor direction by simply moving a jumper
Available Plug-in Options for Logic 3.0 (L3)
Auxiliary Contact: Used to operate security, warning, heating or other 5V to 240V devices. Features both normally open and closed contacts that actuate in conjunction with limit switches.
Warning Signal: Red/green light module provides safety warning prior to close (when using timer-to-close feature). Also supports audio warning devices and includes down mid-stop feature.
CPS3 Option: Enables the addition of a second set of photo-eyes or 2- or 4-wire, self-monitoring edge.
STANDARD FEATURES
Motor: Continuous-duty high-starting torque motor with instant reverse and overload protection. Available in 1/3, 1/2, 3/4 and 1 HP; single- or three-phase. Removable without affecting limit switch settings.
Drive Reduction: First-stage heavy-duty 5L V-belt; second-stage #41 chain; output on trolley #48 chain on 1/3 and 1/2 HP; #41 chain on 3/4 and 1 HP.
Emergency Disconnect: Spring-loaded for emergency manual operation.
Wiring Type: B2, C2, D1 and E2 wiring types are standard and easily set using a selector dial on the Logic 3.0 Control Board (L3). T and TS wiring can be activated with use of a CPS-L or CPS-LN4. Reversing Contactor Units (M) have C2 wiring standard and B2 available by simply moving a jumper wire. Operators are pre-wired to accept a sensing edge, photoelectric sensors, radio controls and most types of access control equipment. Failsafe wiring can be selected with use of a CPS-L, CPS-LN4 or failsafe edge and CPS3 card.
External Radio Control Terminal: Quick, convenient connections for retrofitting or adding radio controls on logic or mechanical operators.
Bearings: Ball bearings on output shaft; heavy-duty, oil-filled bushings on reduction shafts.
Brake: Solenoid-actuated brake is standard on 3/4 and 1 HP units to prevent coasting of door. Optional on 1/3 and 1/2 HP units.
Friction Clutch: Adjustable, helps protect against major damage to door and operator should the door meet an obstruction.
Construction: NEMA 1 type electrical box, heavy-duty 11-gauge steel frame with durable powdercoat finish, all reduction sprockets drilled and pinned to shafts.
Push Button Station: 3-button station comes standard and has OPEN/CLOSE/STOP functionality.
Quick-Mount Header Bracket: For fast, swing-up mounting.
Rail Assembly: High-strength dual L-rail track with nylon quiet-gliding chain guides on rail spacers for quiet, smooth operation.
Warranty: 2-year warranty.
CONTROL ACCESSORIES
CPS® Commercial Protector System®: (recommended) A "non-contact" photo safety sensor designed to sense an obstruction and signal the door operator to reverse to open.
Sensing Edge: (recommended) Designed to sense an obstruction and signal door operator to stop or reverse as desired. An electric or pneumatic sensing device can be added to bottom edge of door.
Spotlight: Liftmaster Brand Model GH Heavy Industrial-Duty
Gear-Reduced Hoist Operator
Model GH is a heavy industrial-duty gear-reduced hoist operator. It features a removable hinged electrical box cover and is easily field-converted in seconds for a left or right-handed drive and hoist.
LOGIC 3.0 TECHNOLOGY (L3)
Added Value
-
Built-in 3-channel, 315MHz radio receiver accepts up to 23 Security+® or unlimited DIP switch remotes. 3-button remotes can be programmed for OPEN/CLOSE/STOP operation
-
Maintenance Alert System™ establishes a routine maintenance schedule based on the number of cycles or calendar date. Includes self-diagnostic system that allows you to troubleshoot up to eight different error codes
-
Timer-to-Close allows programming in 5-sec or 1-min increments. Commercial or industrial photo-eyes required
-
Thermal motor overload can be easily reset from the 3-button floor level control station
Reliability & Programming Simplicity
-
Switchless motor eliminates stuck start switch and motor malfunctions on single-phase operators
-
All high-voltage connections have been removed from the board for safety and ease of service
-
Diagnostic LEDs speed installation and troubleshooting
-
Motor direction jumper lets you change motor direction by simply moving a jumper
Available Plug-in Options for Logic 3.0 (L3)
Auxiliary Contact: Used to operate security, warning, heating or other 5V to 240V devices. Features both normally open and closed contacts that actuate in conjunction with limit switches.
Warning Signal: Red/green light module provides safety warning prior to close (when using timer-to-close feature). Also supports audio warning devices and includes down mid-stop feature.
CPS3 Option: Enables the addition of a second set of photo-eyes or 2- or 4-wire, self-monitoring edge.
STANDARD FEATURES
Motor: Continuous-duty high-starting torque motor with instant reverse and overload protection. Available in 1/2 to 5 HP; single- or three-phase. Removable without affecting limit switch settings.
Auxiliary Chain Hoist: Reduced drive chain hoist with electrically interlocked floor level disconnect for manual operation. Hoist wheel is easily moved to right- or left-hand side of unit, eliminating the need to order left- or right-hand mounting.
Drive Reduction: 45:1 using heavy-duty gears running in oil bath. Cast iron housing. Special "all-climate" synthetic gear oil for greater low-temperature performance.
Emergency Disconnect: Spring-loaded for emergency manual operation.
Wiring Type: B2, C2, D1 and E2 wiring types are standard and easily set using a selector dial on the Logic 3.0 Control Board (L3). T and TS wiring can be activated with use of a CPS-L or CPS-LN4. Reversing Contactor Units (M) have C2 wiring standard and B2 available by simply moving a jumper wire. Operators are pre-wired to accept a sensing edge, photoelectric sensors, radio controls and most types of access control equipment. Failsafe wiring can be selected with use of a CPS-L, CPS-LN4 or failsafe edge and CPS3 card.
External Radio Control Terminal: Quick, convenient connections for retrofitting or adding radio controls on logic or mechanical operators.
Bearings: Sealed roller bearings in gear reducer.
Brake: Solenoid-actuated brake is standard on 3/4 and 1 HP units to prevent coasting of door. Optional on 1/2 HP units.
Construction: NEMA 1 type electrical box, heavy-duty 11-gauge steel frame with durable powdercoat finish, all reduction sprockets drilled and pinned to shafts.
Push Button Station: 3-button station comes standard and has OPEN/CLOSE/STOP functionality.
Warranty: 2-year warranty.
CONTROL ACCESSORIES
CPS® Commercial Protector System®: (recommended) A "non-contact" photo safety sensor designed to sense an obstruction and signal the door operator to reverse to open.
Sensing Edge: (recommended) Designed to sense an obstruction and signal door operator to stop or reverse as desired. An electric or pneumatic sensing device can be added to bottom edge of door.